Pinus roxburghii
Pinus roxburghii (known as chir pine) is a species of pine native to the Himalayas, and named after William Roxburgh.
It generally occurs at lower altitudes than other pines in the Himalaya, from 500–2,000 metres (1,600–6,560 ft), occasionally up to 2,300 m (7,500 ft). The other Himalayan pines are Pinus wallichiana (blue pine), Pinus bhutanica (Bhutan white pine), Pinus armandii (Chinese white pine), Pinus gerardiana (Chilgoza pine) and Pinus densata (Sikang pine).
Pinus roxburghii is a large tree reaching 30–50 m (98–160 ft) with a trunk diameter of up to 2 m (6.6 ft), exceptionally 3 m (10 ft). The bark is red-brown, thick and deeply fissured at the base of the trunk, thinner and flaky in the upper crown. The leaves are needle-like, in fascicles of three, very slender, 20–35 cm (7.9–14 in) long, and distinctly yellowish green.
The cones are ovoid conic, 12–24 cm (4.7–9.4 in) long and 5–8 cm (2.0–3.1 in) broad at the base when closed, green at first, ripening glossy chestnut-brown when 24 months old. They open slowly over the next year or so, or after being heated by a forest fire, to release the seeds, opening to 9–18 cm broad. The seeds are 8–9 millimetres (0.31–0.35 in) long, with a 40 mm (1.6 in) wing, and are wind-dispersed.
Pinus roxburghii is closely related to Pinus canariensis (Canary Island pine), Pinus brutia (Turkish pine) and Pinus pinaster (maritime pine), which all share many features with it. It is a relatively non-variable species, with constant morphology over the entire range.
ITS USES
Chir pine is widely planted for timber in its native area, being one of the most important trees in forestry in northern Pakistan, India and Nepal. For local building purposes, the wood of this tree is the least preferred, as it is the weakest and most prone to decay when compared with other conifers. However, in most low altitude regions, there is no other choice, except for the fact that these being tropical latitudes there are other trees at lower altitudes.
When this species of pine tree reaches a large girth, the bark forms flat patches which can be broken off in chunks (of about 8 inches or 20 centimetres square by 2 in or 5.1 cm thick). It has a layered structure like plywood, but the individual layers have no grain. The locals use this easily carvable bark to make useful items like lids for vessels. Blacksmiths of that region also use this bark exclusively as the fuel for their furnaces.
Old trees which die from fire or drought, undergo some metamorphosis in their wood due to the crystallization of the resin inside the heart wood. This makes the wood become brightly coloured (various shades from translucent yellow to dark red) and very aromatic with a brittle, glassy feel. This form of wood known as jhukti by the locals is very easy to ignite. (It never gets wet or waterlogged.) They use it for starting fires and even for lighting, as a small piece of this burns for a long time (owing to the high resin content). Of all the conifer species in the area, only this one seems to be ideal for that purpose.
Every autumn, the dried needles of this tree forms a dense carpet on the forest floor, which the locals gather in large bundles to serve as bedding for their cattle, for the year round. The green needles are also used to make tiny hand brooms.
The locals of the Jhaunsar region of Uttarakhand have several uses for this tree which is known in the local dialect as salli.
It is also occasionally used as an ornamental tree, planted in parks and gardens in hot dry areas, where its heat and drought tolerance is valued.
ITS VARIOUS FORMS
1. Its trumk
2. Male cones
3. Female cones
